Ninja Circle Slider Spinner Card (IC #5)

Hi everyone! :o)

Today I want to share with you this CAS (clean and simple), Ninja Circle Slider Spinner Card. :o)

This is a CIRCLE SLIDER SPINNER CARD. I made this Interactive Card (IC) for my Celebrating 30 Days of Pisces 2019 personal challenge. If you want to find out more about it, just follow the link provided. :o)

This is a fifth type of IC I made for my challenge. I did create circle slider spinner card for this challenge, but it was double (here), so I considered it as different interactive card type. :o)

I made 15 different types of interactive cards during Pisces period, which was my personal challenge. I completed my challenge, achieved my goals and had a lot of fun. I wrote a short review about the challenge here.

How I made this card...

To make this card I used a super cute Mama Elephant 'Tiny Ninjas' stamp set. LOVE!!! :o)

I colored a Ninja during Kathy's Racoosin 12th 30 Day Coloring Challenge. You can see all my coloring samples during the challenge here.

I stamped the adorable ninja on a watercolor paper and watercolored him using Distress Inks. After drying, I fussy cut the ninja and traced edges with black marker.

I stamped one more ninja on a white cardstock paper, colored ninja with black marker and fussy cut him, this time leaving white thin border around him.

I glued both images together, the watercolored ninja over the black one. I did this because the watercolor paper I use is very thin and I needed thicker image for my card.

Then I prepared a top folded card base and a white cardstock paper panel, both same size.

I cut two concentric circles on the panel using EK Success Circle Cutter, removed the circle belt and stamped a sentiment in a small circle.

I stamped tiny ninja stars (Shuriken) on the panel and on the small circle and loosely watercolored them with a Distress Ink Hickory Smoke.

For a slider mechanism, I used a plastic button and a plastic letter bead. I glued them together and left aside for an hour. I didn't use any special glue. I used UHU all purpose liquid glue. It works great, there is just some patience required and I have a lot of that. :o)

With all parts ready, I assembled the card. I glued 3-D foams on the panel, glued the panel on the card base and placed the slider mechanism on the card base. I glued 3-D foams on the sentiment circle and glued it on the card base. To center it perfectly, I used that cut out circle belt left from cutting the panel as a guide. :o)

Then I tested if the mechanism is working. I glued the ninja on the slider mechanism, left it dry for an hour and my card was finished. :o)

I love how my card turned out. Here is a short video. :o)

Music:
"Marty Gots a Plan" Kevin MacLeod   

(incompetech.com)
Licensed under Creative Commons: By Attribution 3.0
http://creativecommons.org/licenses/by/3.0/

Card measurements: 95 mm x 127 mm (3 3/4" x 5")

List of supplies:

• Mama Elephant 'Tiny Ninjas' stamp set
• white cardstock paper
• watercolor paper
• Ranger's Archival Ink (Jet Black)
• Tim Holtz's Distress Inks:

• Tea Dye
• Hickory Smoke
• Stabilo Fiber Tip Pen (Marker) 68/46, Black
• plastic button
• plastic letter bead
• UHU liquid glue
• 3-D foam squares, 5 x 5 x 3 mm
• acrylic block (102 mm x 102 mm)
• Fiskars High Precision Personal Paper Trimmer
• EK Success Circle Cutter
• Xcut Self Healing Cutting Mat A4
• bone folder
• scissors
• Marabu rounded fine paint brush no. #0
• water
• paper towels

Thank you for stopping by and your kind feedback. Enjoy and smile! :o)

Milka